American Standard Bathroom Aids 6032 Series Seated Shower Base User Manual

INSTALLATION INSTRUCTIONS  
6032 SERIES TUB  
6032 SERIES SEATED SHOWER BASE  
HIGH GLOSS ACRYLIC SURFACE  
Thank you for selecting American Standard...the benchmark of fine quality for over 100 years.To ensure  
that your installation proceeds smoothly--please read these instructions carefully before you begin.  
BEFOREYOU BEGIN....  
Local building codes vary by location. Observe all local plumbing and building codes.  
Your new bath is shipped to you after careful inspection.  
To insure maximum performance and pleasure from this product, please follow the instructions and cautions.  
TOOLS & MATERIALS REQUIRED  
MATERIALS:  
• Nails  
TOOLS:  
• Level  
• Screw Driver  
• Plumber’s Putty  
• Silicone Sealant  
• 1 x 3 or 2 x 4 Stringers  
• Drop Cloth  
• Square  
• Standard Woodworking Tools  
• Personal Safety Equipment  
• Caulking Gun  
Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Mortar Mix or Grout  
NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.  
ROUGH-IN INFORMATION:  
6032 SERIES TUB  
ROUGH-IN INFORMATION:  
6032 SERIES SEATED SHOWER BASE  
60"  
(1524mm)  
60"  
(1524mm)  
9-3/4"  
(248mm)  
3-3/16"  
(81mm)  
1-3/8"  
(35mm)  
8"  
(203mm)  
15-5/8"  
(397mm)  
15-5/8"  
(397mm)  
14-7/8"  
(378mm)  
31-1/4"  
(794mm)  
25-5/8"  
(651mm)  
32"  
(813mm)  
3-3/16"  
(81mm)  
1-1/8"  
(29mm)  
1-1/8"  
(29mm)  
3-1/2"  
(89mm)  
3-15/16"  
(100mm)  
2" (51mm)  
C/L OF DRAIN  
3"  
(76mm)  
1"  
(25mm)  
1"  
(25mm)  
17-3/4"  
15-5/16"  
(451mm)  
18"  
(457mm)  
(389mm)  
STRINGER  
HEIGHT  
SEAT HT.  
19"  
(483mm)  
GENERAL SPECIFICATIONS FOR 6032 SHOWER BASE  
GENERAL SPECIFICATIONS FOR 6032 TUB  
60 x 32 x 19 In.  
(1524 x 813 x 483mm)  
60 Lbs. (27 Kg)  
INSTALLED SIZE  
60 x 32 x 18 In.  
INSTALLED SIZE  
(1524 x 813 x 457mm)  
60 Lbs. (27 Kg)  
WEIGHT  
WEIGHT  
WEIGHT w/WATER  
GAL. TO OVERFLOW  
BATHING WELL AT SUMP  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
(PROJECTED AREA)  
PTS.  
N/A  
N/A  
N/A  
N/A  
WEIGHT w/WATER  
493 Lbs.(224 Kg)  
52 Gal. (197 L)  
22 x 44.5 In. (559 x 1130mm)  
25 X 53 In.(635 x 1346mm)  
12 In. (305mm)  
GAL. TO OVERFLOW  
BATHING WELL AT SUMP  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
N/A  
<15 Lbs./Sq.Ft. (<75 Kgs/Sq.m)  
37 Lbs./Sq.Ft. (181 Kgs/Sq.m)  
(PROJECTED AREA)  
PTS.  
27.5  
29.4  
27.5  
28.9  
CUBE (FT )  
CUBE (FT2)  
3
754731-100 Rev. D  
All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.  
© AS America, Inc. 2012  
 
2
A.) THIS BATH MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM. We recommend the use of mortar as  
bedding material (sand is not recommended). Apply enough bedding to support the complete bottom of the bath. After  
the bedding has been poured, and before it sets, position the bath within the recess until the rim is leveled against the  
leveling stringers (see "Typical Recess Installation") shown below. The rim of the bath MUST NOT support weight.  
Allow the bedding material to completely harden before applying weight to the rim or bottom of the bath.  
TYPICAL RECESS INSTALLATION  
60-3/16"  
(1529mm)  
LEVELING  
STRINGERS  
B.) Check level front to back and side to side, shim as necessary. To secure the tub to wood studs, use drywall screws  
with flatwashers or roofing nails immediately above the flange of the bath. To secure the tub to steel studs, use 4"  
drywall screws and flatwashers.  
TYPICAL FLANGE MOUNTING DETAIL  
SUGGESTED BATH  
INSTALLATION METHOD  
STEEL  
STUD  
WOOD  
STUDS  
STUD  
TILE  
STEEL  
STUDS  
WASHER  
WATERPROOF DRYWALL  
OR CEMENT BOARD  
WASHER  
WATERPROOF DRYWALL  
OR CEMENT BOARD  
DRYWALL SCREW  
OR ROOFING NAIL  
TILE  
SEALANT  
SEALANT  
4" (102mm)  
DRYWALL  
SCREW  
TUB  
TUB  
1" x 3" (25 x 76mm) WOOD  
STRINGER FULL LENGTH  
1" x 3" (25 x 76mm) WOOD  
STRINGER FULL LENGTH  
SECURE THE BATH TO THE STUDS AS SHOWN FOR  
WOOD OR STEEL STUD CONSTRUCTION.  
C.) Any finish material such as tile or wallboard must be self-supporting if it contacts the deck of the bath.  
Flooring will be butted against the bottom of the tub apron, also holding the tub in place.  
3
DRAIN CONNECTION  
Using recommended drain opening, connect bath drain to waste line. Tighten all drain joints securely.  
754731-100 Rev. D  
3
 
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.  
Do not use wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may  
be removed using granular Spic and Span® mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
FEATURES ofYOUR NEW AMERICAN STANDARD ACRYLIC BATHTUB  
Your new acrylic bathtub has been molded in the newest plumbing fixture material available today. Acrylics are tough durable finishes  
that are simple and easy to care for. The colors have been formulated to match other American-Standard fixtures and enhance your  
choice of bathroom decorations. The high gloss surface is resistant to impact and chemicals and will retain its lasting luster with  
proper care and maintenance.  
AFTERCARE and CLEANING  
• Always fill the tub with temperate water. Excessively hot water may cause surface damage.  
• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.  
• Clean after use with a mild liquid household detergent cleaner. Abrasive cleaners such as Lestoil, Lysol Disinfectant (spray or  
concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or cleaning  
products in aerosol cans should not be used.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits, or other surface blemishes.  
• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses its sheen, dulled areas  
can be restored by rubbing with a white polishing compound and waxing with a "liquid wax."  
Do not wax areas where you walk or stand.  
• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into contact with the surface.  
• Clean the surrounding surface immediately after using caustic drain cleaners.  
• Burning cigarettes will damage the surface.  
• Should damage to the fixture occur, repairs can be made quickly and easily.Your distributor or builder can provide details.  
®
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE  
AS America, Inc. Limited Lifetime Warranty for Tubs and Shower Bases  
AS America, Inc. (American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this tub/shower base – American Standard,  
in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser.  
(30) days of purchase.  
In no event will American Standard be liable for the cost of repair or replacement of any installation materials including but not limited to tile, marble, etc.  
This limited warranty does not apply to Commercial Installations. The warranty for Commercial Installations is three (3) years.  
This limited warranty DOES NOT COVER the following:  
1. Defect or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and cleaning as directed in the Installation  
Instruction Manual and use of other than genuine American Standard replacement parts, in all cases whether caused by a plumbing contractor, service company, the  
owner or any other person.  
2. Deterioration through normal wear and tear and the expense of normal maintenance.  
3. Commercial application.  
4. Options and accessories. American Standard's limited warranty on these items is one year for parts only and excludes labor. This one year limited warranty covers  
accessories manufactured by American Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against defects of material or workmanship. Warranty coverage  
begins on the date the accessory was originally purchased by the owner.  
5. Shipping cost for returning products for repairs or replacement under the limited warranty and labor or other cost incurred in connection with product removal or  
installation under this limited warranty.  
6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED, OR THE EXTENSION BEYOND  
THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR AN INTENDED  
PURPOSE. (Some jurisdictions do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so  
these limitations and exclusions may not apply to you.)  
7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly, distributors, retailers, dealers, installation contractors and  
users of plumbing products should determine whether there are any code restrictions on the installation or use of a specific product.)  
This limited warranty gives you specific legal rights.You may have other statutory rights that vary from state to state or from province to province, in which case this  
warranty does not affect such statutory rights.  
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service  
request (including a description of the product model and of the defect) be sent to the following address:  
In Canada:  
AS Canada ULC  
5900 Avebury Rd.  
Mississauga, Ontario  
Canada L5R 3M3  
In Mexico:  
In the United States:  
American Standard Brands  
P.O. Box 6820  
American Standard B&K Mexico  
S. de R.L. de C.V.  
Via Morelos #330  
Col. Santa Clara  
Ecatepec 55540 Edo. Mexico  
Toll Free: 01-800-839-1200  
Piscataway, New Jersey 08855  
Attention: Director of Consumer Affairs  
Toll Free: (800) 387-0369  
For residents of the United States, warranty  
information may also be obtained by calling  
the following toll free number: (800) 442-1902  
754731-100 Rev. D  
4
 

Accusplit Heart Rate Monitor 605XE User Manual
Acoustic Research MP3 Docking Station ARS28I User Manual
Aga Ranges Cooktop DESN 513534 User Manual
Aiwa Speaker System TS W45 User Manual
Alpine Cassette Player HCE 100XM User Manual
AMD Computer Hardware GA K8NSC 939 User Manual
American Standard Outdoor Shower T00050X User Manual
AOSafety Welding System Weld Cool User Manual
Ask Proxima Projector C447 User Manual
Atlona Switch AT SDI81 User Manual