Airlink101 Switch ASW308 User Manual

Quick Installation Guide  
8-Port 10/100 Mbps  
Green Switch  
Model# ASW308  
Ver. 1A  
 
Section 1  
Hardware Description  
Front Panel  
LED Indicators  
LED  
Color  
Status  
Description  
On  
The switch is powered on.  
The switch is powered off.  
LAN port is connected.  
POWER  
Green  
Off  
On  
LNK/ACT Green  
Off  
LAN port is not connected.  
Transferring or receiving data.  
Flashing  
Rear Panel  
Item Name  
Power  
Description  
Power connector, DC 8V / 0.6A.  
10/100 Mbps LAN ports 1 to 8.  
1 - 8  
 
Section 2  
Connecting the Switch  
Note: Operating Environment  
This switch must be installed and operated within the limits of specified  
operating temperature (32~1310F) and humidity (10~90%  
Non-condensing). Do not place objects on top of the unit. Do not obstruct  
any vents at the sides of the unit. Do not position the unit near any  
heating source such as heater, radiator, or direct exposure to sun.  
Prevent entering of water and moisture into the unit. If necessary, use  
dehumidifier to reduce humidity.  
Step 1 Connecting to network devices  
The RJ-45 ports on the switch support Auto-MDI/MDI-X function which  
allows using straight-through or cross-over type cables to connect this  
switch to workstation or hub.  
Connect one end of the network cable to the RJ-45 port on the rear panel,  
and connect the other end of the network cable to the RJ-45 port on the  
network device. Follow the same procedure to connect all the RJ-45 ports  
of the switch. The UTP network cables must be two pairs Category 5 for  
100Mbps data transmission; two pairs Category 3, 4 or 5 standards for  
10Mbps data transmission. Maximum length, using UTP cable, between  
the switch and connected device is 100 meters (300ft).  
Step 2 Connecting the power  
Connect the output end of the power adapter to the power connector on  
the right panel of the switch. Connect the power adapter to the power  
outlet. The green Power LED on the front panel should be lit. Once the  
network cable is connected to both ends in Step 1 and the attached  
network device is powered on, the green LNK/ACT LED should be lit.  
 
Section 3  
Troubleshooting  
1. Power LED is not lit  
Check if the power adapter is properly connected to the power outlet.  
Make sure the power jack is firmly plugged into the power socket of  
the switch.  
2. Link/Activity is not lit when connect to 10/100 Mbps device  
Check the power switch of the network device attached to the switch;  
make sure it is turned ON.  
Check the network cable; make sure it is properly connected to the  
switch and the network device.  
Check the network cable; make sure the UTP cables comply with the  
specifications described in Section 2.  
 
Section 4  
Technical Support  
*Power savings may vary depending on products used. Actual data throughput will vary.  
Network conditions and environmental factors lower actual data throughput rate.  
Specifications are subject to change without notice. All rights reserved. Copyright © 2011  
AirLink101®. AirLink101®, the stylized AirLink101® logo, specific product designations, and  
all other words and logos that are identified as trademarks and/or service marks are, unless  
noted otherwise, the trademarks and service marks of AirLink101®. All other product or  
service names are the property of their respective holders. AirLink101® products are  
protected under numerous U.S. and foreign patents and pending applications, mask work  
rights, and copyrights.  
 

Aiphone Stereo Amplifier PG 3 User Manual
Air King Electric Heater 1DKX3 8900 User Manual
Allied Telesis Network Card GE8 User Manual
Amcor Dehumidifier Ad 140 User Manual
American Audio Portable Multimedia Player SDJ 2 User Manual
Ask Proxima Projector C440 C450 User Manual
ATI Technologies Computer Hardware GL 8800 User Manual
ATI Technologies Lawn Mower Lawn Mower User Manual
Axor Indoor Furnishings 92720000 User Manual
Barco DVR R5900001 02 User Manual