• Master or single drive: To configure the drive as a master or a single
drive, set the jumper on pins 7 and 8.
• Drive is slave: To configure the drive as a slave, or second drive on
®
Barracuda ATA IV Family Installation Guide
the cable, remove all the jumpers.
ST380021A, ST360021A, ST340016A, ST320011A
• Master with non ATA-compatible slave: Use this setting if the slave
drive is not recognized. Configure the master drive with a jumper set on
pins 5 and 6 and pins 7 and 8 to enable this option.
Publication number:100129216, Rev.A
The Easiest Way to Install Your Drive
• Cable select option: Cable Select jumpers use the cable to determine
master or slave. To enable cable select, set a jumper on pins 5 and 6. If
using two drives, jumpers for both drives should be set on pins 5 and 6.
DiscWizard is Seagate’s exclusive Windows program that is included with
your drive for easy drive installation. You can use this software if you have a
bootable hard drive in your computer and are running Windows Me,
Windows 98 or Windows 95. Download the software from our Web site at
• Alternate capacity jumper: Drives with a 40-Gbyte capacity and
greater are limited to 32 Gbytes. This jumper is used to provide a
solution to specific legacy BIOS problems. When using the alternate
capacity jumper, Disk Manager software is required to achieve the
drive’s full capacity.
.
Run DiscWizard before installing your drive for customized step-by-step
instructions for your system.
Attaching Cables and Mounting the Drive
To run DiscWizard:
instructions to complete the installation.
If you cannot run DiscWizard, follow the instructions on this installation
sheet to install and configure your drive.
1. Attach one end of the drive interface cable to the interface connector
on your computer’s motherboard (see your computer manual for
connector locations).
Caution. Align pin 1 on the motherboard connector with pin 1 on
your drive connector. Pin 1 is marked by a stripe on one side of the cable.
!
What You Need
• A Phillips screwdriver and four 6-32 UNC drive mounting screws
2. Attach the interface connector and the power connector to the drive.
Note. You can mount the drive in any orientation. Usually it is mounted
• A standard 40-pin ATA interface cable, or an 80-conductor cable to run
with the circuit board down.
Ultra ATA 100 (max length: 18 inches)
3. Secure the drive in the computer using four 6-32 UNC mounting
screws in either the side-mounting or bottom-mounting holes. Insert
the screws no more than 0.20 inch (5.08 mm) into the bottom-mounting
holes and no more than 0.14 inch (3.55 mm) into the side-mounting holes.
• An unused drive power cable for your new drive
• A version of Windows with FAT32 file system for drives over 32 Gbytes
Ultra ATA/100 Requirements
Note. When configuring two ATA devices on
The drive can be configured to support a default maximum transfer rate.
This drive can support transfer rates up to 100 Mbytes per second
(UDMA 5) in Ultra ATA/100 mode. Using a software utility, you can set the
default transfer rate to the best capability of your system. For your drive to
run in this mode, you need the following:
the same cable, both must use Cable
Select or both must use Master/Slave
Master
Pin 1
jumper settings. If using a standard
40-pin cable, the master and slave
drives can be placed in any position. If
using a 40-pin 80-conductor cable, attach
the blue connector to the motherboard,
the black connector to the master drive
and the grey connector to the slave.
Computer
Motherboard
Slave
• A computer that supports UDMA mode 5
• A 40-pin 80-conductor cable (available from your dealer)
Caution. Do not overtighten the screws or use metric screws. This
• A software utility to confirm and activate Ultra ATA/100. Seagate® provides
a utility called UATA100.exe. You can download the latest version from our
!
may damage the drive.
• Windows Me or Windows 98 operating system: either supports Ultra
Power
connector
ATA\100.
Handling Precautions
Disc drives are extremely fragile. Do not drop or jar the drive.
Interface
connector
Pin 1
Keep the drive in the protective SeaShell container until you are
ready to install it. This minimizes handling damage.
The drive has a protective cover called SeaShield®. Do not remove
this permanent cover—it protects the drive from electrostatic
discharge (ESD) and minor impact damage.
Configuring the BIOS
For your computer to recognize your new drive, configure your
computer’s BIOS as follows:
Protect your drive from static discharge by wearing a grounded wrist
strap throughout the installation process.
1. Run the system setup program.
Always handle the drive by the edges or frame.
2. Enable LBA mode and UDMA mode, if available.
Do not apply pressure or attach labels to the circuit board or the
top of the drive.
3. Select the auto-detect option. If necessary, refer to the drive param
eters on your drive label to configure the drive for your system. BIOS
capacity of the drive, use LBA mode or use Disk Manager.
Setting the Jumpers
Options jumper block
Refer to the jumper settings
4. Save and exit the system setup program.
*Master or single drive
on your drive label to
configure the drive for your
system. Jumper settings also
can be accessed online from
our Web site at
BIOS Settings
Drive is slave
Master with non ATA-
compatible slave
Drive Model
ST380021A
ST360021A
ST340016A
ST320011A
Formatted Gbytes
Total Sectors*
156,301,488
117,231,408
78,165,360
80.0
60.0
40.0
20.0
*Cable select
Limit drive capacity
>32 Gbytes = 32 Gbytes
<32 Gbytes = 2.1 Gbytes
39,102,336
7
8
5
6
3
4
1
2
*Drives may be shipped with
either configuration as default.
Circuit Board
*One sector equals 512 bytes.
|